Monthly Archives: December 2024

Magnetism Detector | Project 12/20 | Maxitronix 20in1 | Learning Electronics In The Lab With Jay Jay

Posted on by
Reply

This post is part of my video blog and you can find more information about this video over here.

You can support this channel on Patreon: patreon.com/JohnElliotV

In this video I do the 12th project from the Maxitronix 20in1 (the Sensor Robot 20): Magnetism Detector.

In this project we control a BJT transistor with a magnetic reed switch.

We use the thermal camera to observe heat in the transistors and LEDs during operation.

This is a plain DC circuit with no signals so there was no call for measuring anything with the oscilloscope.

I got myself a little confused about normally open and normally closed circuits during the video, but I think I was clear enough about that in the end.

Thanks very much for watching! And please remember to hit like and subscribe! :)




Following is a product I use picked at random from my collection which may appear in my videos. Clicking through on this to find and click on the green affiliate links before purchasing from eBay or AliExpress is a great way to support the channel at no cost to you. Thanks!

Yutiars Round Paint BrushesThis is an image of the product.notes

Let’s go shopping!

Equipment from Peak Electronic Design

Posted on by
Reply

The British company Peak Electronic Design has a wonderful range of Test Instruments.

Today I purchased these ones:

Still on my wish list is this one:

The reason for this particular splurge is that after I purchased my METCAL PS-900 Soldering Station element14 sent me an email with a coupon for 15% off. Since these Peak Atlas devices were on my wish list I figured I might as well get them while I can get 15% off.

METCAL PS-900 Soldering Station

Posted on by
Reply

Update: my notes about my METCAL PS-900 soldering station are on my personal wiki, over here: METCAL PS-900 Soldering Station.

The other day I was doing some soldering with my Horusdy Soldering Station but I got the feeling its soldering iron was under performing. I just wasn’t getting good solder joints even though I was using good solder and plenty of flux.

So today I did some research and found myself a new soldering station: METCAL PS-900 Soldering Station. I found one for sale on element14 for AU$458.59 which as far as I can tell was a really good price. They were going for more like AU$700+ on Amazon, eBay, and even AliExpress.

I did also research and consider some other options from JBC, Metcal, Weller, and Hakko.

I also picked up a couple of spare tips:

The tip it came with was the METCAL SFV-CH10, 30° Chisel, 1.5 mm Soldering Iron Tip.

I am expecting that the 1 mm chisel tip is going to be my weapon of choice, so I got two of those. (Update: this was a mistake, the 1.5mm or 2mm option would have been a better choice.)

Conspicuously absent on this soldering station is a temperature setting. That’s because these METCAL irons come with SmartHeat technology, as ChatGPT explains. For the SFV-CH10 the Curie point is designed to maintain a nominal tip temperature of around 380 °C (715 °F) under typical load conditions.

Mail Call #15: iPhone 6s, USB Accessories, Software Books, IEC Power Adapters, and More!

Posted on by
Reply

This post is part of my video blog and you can find more information about this video over here.

You can support this channel on Patreon: patreon.com/JohnElliotV

In this video I open the stuff that has arrived in the mail recently:

I mention that I’m working on a new book teardown for God Created the Integers.

The epaper modules I’m working with are these ones: WeAct 2.9” 2.13″ 2.9 2.13 Inch Epaper Module E-paper E-Ink EInk Display Screen SPI Black-White Black-White-Red and the microcontrollers I’m experimenting with are these ones: WeAct ESP32 ESP-32 ESP32C3 ESP32-C3FH4 Development Board Wireless WiFi Bluetooth-compatible Module Micropython.

The Arduino Nano you see is one of these: Mini / Type-C / Micro USB Nano 3.0 With the bootloader compatible Nano controller for arduino CH340 USB driver 16Mhz ATMEGA328P connected to an OLED display like this: 1.3″ OLED Display Module White/Blue Color Drive Chip SH1106 128X64 1.3 inch OLED LCD LED IIC I2C Communicate.

The video I mention about the test clips is this one: Unboxing #9: Unboxing of Sudake SDK07 and SKD08 IC Clip SMD Gripper Test Probe | In The Lab.

If you’re interested in the old iPhone 6s you can find more information at Wikipedia: iPhone 6s or from Apple: iPhone 6s – Technical Specifications.

My iPod touch is 7th generation, you can get more info from Apple: iPod touch (7th generation) – Technical Specifications.

I mention that I listen to di.fm. If you’re into electronic music, check it out.

I keep my notes which I display on my bench iPhones on the web, over here: https://www.jj5.net/display/

Thanks very much for watching! And please remember to hit like and subscribe! :)

Following is a product I use picked at random from my collection which may appear in my videos. Clicking through on this to find and click on the green affiliate links before purchasing from eBay or AliExpress is a great way to support the channel at no cost to you. Thanks!

3ELIGHTING 10″-26″ VESA Wall MountThis is an image of the product.

Let’s go shopping!

ESP-NOW instead of WiFi

Posted on by
Reply

Today I learned about ESP-NOW over here: Forget WiFi! This Wireless Method is WAY Better?

This looks like exactly what I need for a project I’m planning. I want to connect my WiFi router with a relay between its power source. I can then trip the relay to reboot the router. I need to do this every couple of months and doing it manually is a pain because I have to walk into the other room to do it.