Weather Indicator | Project 20/20 | Maxitronix 20in1 | Learning Electronics In The Lab With Jay Jay

This post is part of my video blog and you can find more information about this video over here.

You can support this channel on Patreon: patreon.com/JohnElliotV

In this video we do the 20th project from the Maxitronix Sensor Robot 20 (20in1) Electronics Project Lab Kit: Weather Indicator.

We use the Rigol MSO5074 Mixed Signal Oscilloscope to have a look at the two square waves from the astable multivibrators.

We use the UNI-T UTi260B Thermal Imager to investigate the circuit’s heat profile.

We use the Riden RD6006 Bench Power Supply to deliver 9V to power the circuit and to report on its current draw.

Thanks very much for watching! And please remember to hit like and subscribe! :)





Following is a product I use picked at random from my collection which may appear in my videos. Clicking through on this to find and click on the green affiliate links before purchasing from eBay or AliExpress is a great way to support the channel at no cost to you. Thanks!

Yum Cha Macro Programmable 8-Key Mechanical KeyboardThis is an image of the product.

Let’s go shopping!

Touch Buzzer | Project 19/20 | Maxitronix 20in1 | Learning Electronics In The Lab With Jay Jay

This post is part of my video blog and you can find more information about this video over here.

You can support this channel on Patreon: patreon.com/JohnElliotV

In this video we do the 19th project from the Maxitronix Sensor Robot 20 (20in1) Electronics Project Lab Kit: Touch Buzzer.

This circuit uses a Darlington pair to amplify the very weak signal from the touch sensor.

We use the Rigol MSO5074 Mixed Signal Oscilloscope to look at the square wave from the astable multivibrator.

We use the UNI-T UTi260B Thermal Imager to examine the thermal characteristics of the circuit, particularly the 1K resistors getting warm.

We use the Riden RD6006 Bench Power Supply to provide 9V for our circuit and also to measure the current drawn by the circuit in its inactive (11mA) and active (12mA) states.

Thanks very much for watching! And please remember to hit like and subscribe! :)





Following is a product I use picked at random from my collection which may appear in my videos. Clicking through on this to find and click on the green affiliate links before purchasing from eBay or AliExpress is a great way to support the channel at no cost to you. Thanks!

Maxitronix 500in1 Electronics Project Lab KitThis is an image of the product.notes

Let’s go shopping!

Rain Detector | Project 18/20 | Maxitronix 20in1 | Learning Electronics In The Lab With Jay Jay

This post is part of my video blog and you can find more information about this video over here.

You can support this channel on Patreon: patreon.com/JohnElliotV

In this video we do the 18th project from the Maxitronix Sensor Robot 20 (20in1) Electronics Project Lab Kit: Rain Detector.

We use the Rigol MSO5074 Mixed Signal Oscilloscope to see the 1.6 kHz square wave from our astable multivibrator.

We use the UNI-T UTi260B Thermal Imager to watch the thermal effects of the circuit. We see both the 1K resistors in the astable multivibrator get warm, but only the activated side of the bistable multivibrator gets warm.

We use the Fluke 17B+ Digital Multimeter to buzz out the circuit looking for mistakes.

We use the Riden RD6006 Bench Power Supply to provide 9V for our circuit. I make a mistake and connect it the wrong way around to begin with!

Thanks very much for watching! And please remember to hit like and subscribe! :)





Following is a product I use picked at random from my collection which may appear in my videos. Clicking through on this to find and click on the green affiliate links before purchasing from eBay or AliExpress is a great way to support the channel at no cost to you. Thanks!

TOOKKS HZY ABS Wire FixtureThis is an image of the product.notes

Let’s go shopping!

Low-Water Indicator | Project 17/20 | Maxitronix 20in1 | In The Lab With Jay Jay

This post is part of my video blog and you can find more information about this video over here.

You can support this channel on Patreon: patreon.com/JohnElliotV

In this video we do the 17th project from the Maxitronix Sensor Robot 20 (20in1) Electronics Project Lab Kit: Low-Water Indicator.

We use the Rigol MSO5074 Mixed Signal Oscilloscope to see the output of the astable multivibrator. In the video I make a mistake and attach the probe to the wrong pins.

We use the METCAL PS-900 Soldering Station to solder the wires I use for the banana plugs I attach to the touch sensor an voice sensor (microphone).

We use the UNI-T UTi260B Thermal Imager to look at the heat profile of the circuit. We see that the low resistances (470Ω and 1KΩ) get the warmest, but the higher resistances (e.g. 10KΩ) are also slightly visible.

We use the Fluke 17B+ Digital Multimeter to check the resistance of the touch sensor.

We use the Peak Electronic Design Atlas LCR45 LCR Meter to measure the resistance of the resistor we use in the LED attachment circuit. This extra circuit allows us to switch out the buzzer for an LED, which makes a lot less racket. The resistor it uses turned out to be 470Ω.

We use the Riden RD6006 Bench Power Supply to provide 9V for our test circuit. Usually I take a current reading to see how much power the circuit draws in its various states, but I forgot!

We use the Horusdy Soldering Station with Hot Air Gun for its hot air gun in order to shrink the heat shrink which we added to the banana plug cables we attached to our sensors.

Thanks very much for watching! And please remember to hit like and subscribe! :)





Following is a product I use picked at random from my collection which may appear in my videos. Clicking through on this to find and click on the green affiliate links before purchasing from eBay or AliExpress is a great way to support the channel at no cost to you. Thanks!

Yum Cha 9-Inch Needle Nose PliersThis is an image of the product.notes

Let’s go shopping!

Burglar Alarm | Project 11/20 | Maxitronix 20in1 | Learning Electronics In The Lab With Jay Jay

This post is part of my video blog and you can find more information about this video over here.

You can support this channel on Patreon: patreon.com/JohnElliotV

In this video I do the 11th project from the Maxitronix 20in1 (the Sensor Robot 20): Burglar Alarm.

This project uses the reed switch to trigger a bistable multivibrator that controls an alarm. The bistable multivibrator can be reset with the key. An astable multivibrator is used to generate the tone for the audible alarm.

In this project we get some more experience with transistors and how they can be used in various types of multivibrator circuit. Under the thermal camera we can see some of the transistors warming up as they conduct electricity. With the oscilloscope we can see the periodic waveform used to generate the alarm tone.

Note: while I was making this video I needed to make some banana plug to hook clip cables (so that I could test the reed switch). I made a video of my making those cables which you can see here: Electronics Project #9: Making Banana Plug to Hook Clip Cables | In The Lab With Jay Jay.



Thanks very much for watching! And please remember to hit like and subscribe! :)


Following is a product I use picked at random from my collection which may appear in my videos. Clicking through on this to find and click on the green affiliate links before purchasing from eBay or AliExpress is a great way to support the channel at no cost to you. Thanks!

Yum Cha KT-908 Digital ThermometerThis is an image of the product.

Let’s go shopping!

Speech Conductor | Project 10/20 | Maxitronix 20in1 | Learning Electronics In The Lab With Jay Jay

This post is part of my video blog and you can find more information about this video over here.

You can support this channel on Patreon: patreon.com/JohnElliotV

In this video I do the tenth Maxitronix 20in1 Electronic Project Lab project: Speech Conductor.

In this project we learn a little about transistors, amplifiers, and astable multivibrators.

Note: while I was making this video I took a detour into making a cable, which didn’t work out. You can see the video about that over here: Extra Content #13: Failing to Attach Banana Plugs to Microphone Cables | In The Lab With Jay Jay.



Thanks very much for watching! And please remember to hit like and subscribe! :)


Following is a product I use picked at random from my collection which may appear in my videos. Clicking through on this to find and click on the green affiliate links before purchasing from eBay or AliExpress is a great way to support the channel at no cost to you. Thanks!

ALKOY Capacitor Discharge PenThis is an image of the product.notes

Let’s go shopping!